Water Driven Proportioning Pumps

Home
Up
HydroBlend 6000 Series
Mix Ratios & Percentages
HydroBlend DI Pump
Venturi Proportional Mixers
Water Driven Proportioning Pumps

 

Water Driven Proportioning pumps from  Coolant Consultants, Inc.

Proportional mixers are used to properly mix concentrates with water producing working solutions and make-up solutions.  Typical applications for proportional mixing pumps are coolants, cleaners, strippers, degreasers, fertilizers, and fungicides.

bullet

Save labor by mixing faster than by hand

bullet

Automatic models save even more by keeping containers full unattended

bullet

More accurate than hand mixing

bullet

Safer because less contact with concentrates

bullet

Lean coolant mixtures can cause excessive tool wear, corrosion on parts and machines, and increased bacteria growth

bullet

Rich coolant mixtures can cause sticky or slippery residues, operator irritation, and waste expensive concentrate

bullet

Lean cleaner mixtures won't perform as intended

We carry two types of proportional mixers

bullet

Venturi types use water passing over an orifice to create suction that draws the concentrate from the container and mixes it with the water.  Concentration is controlled by either changing orifice size or turning a metering valve.  These units can not operate with any back pressure, so they can only be used to fill a pail or nearby container.  Accuracy is also affected by water pressure and concentrate level.

bullet

Link to Venturi Proportional Mixers

bullet

Water Driven Pumps use water to drive a piston which pumps concentrate into a mixing chamber where it is mixed with the water.  Concentration is not affected by water pressure or concentrate level, which makes them very accurate.  These units can be hooked up in-line or to a hose reel and are typically used in central distribution systems.

bullet

Note  Plumbing codes in some areas may require a backflow preventer or other types of controls before the mixing system.  Also, it is always recommended (and required for the warranty) to install a screen filter before the mixer.

bullet

NEED HELP calculating your mix ratio or percentage?  Click here.

bullet

Note:  The mixture ratios and percentages presume chemicals with the approximate viscosity of water.  A substantial increase in viscosity can reduce the proportioning specifications of the pump. 

 

 

6180 A-V

Proportional Mixer

HydroBlend6180 cropped.jpg (70908 bytes)

 

HydroBlend™ Precision Water Powered Coolant Metering Pumps

HYDROBLEND "6000" Series Proportioning Pumps

Can be used with lower volume applications such as hose reels, in-line, and central mixing systems. Very accurate.  The "6000" Series are the high-end pumps, not the value-priced.

bullet

7 gpm @ 75 psi

bullet

Acrylic pump head

bullet

Viton seals standard 

bullet

Stainless steel valve block, outlet fitting, and main cylinder

bullet

Reduces chemical waste, improves proportioning accuracy, repeatable formulations, easy installation, and reliable operation

bullet

Water pre-filter included - 200 mesh/50 micron cleanable screen, garden hose fittings  

bullet

6005 A-V  .5 oz. -.04% to .35% mix ratio  $866.00

bullet

6010 A-V  1.0 oz. - .08% to .75% mix ratio  $820.00

bullet

6015 A-V  1.5 oz. - .12% to 1.15% mix ratio  $820.00

bullet

6020 A-V  2 oz. - .15% to 1.50% mix ratio  $820.00

bullet

6040 A-V  4 oz. - 0.30% to 3.00% mix ratio  $834.00

bullet

6080 A-V  8 oz. - .60% to 5.80% mix ratio  $844.00

bullet

6120 A-V 12 oz. - .95% to 8.50% mix ratio  $1034.00

bullet

6180 A-V 18 oz. - 1.40% to 12.30% mix ratio  $1067.00 - In Stock - Our best-selling pump!

bullet

6200 A-V  20 oz. - 1.60% to 13.50% mix ratio  $1067.00

bullet

6320 A-V  32 oz. - 2.40% to 20.00% mix ratio  $1129.00

bullet

6470 A-V  47 oz. - 3.20% to 26.80% mix ratio - 9.5 US gpm  $1196.00

bullet

6850 A-V 85 oz. - 4.70% to 33.00% mix ratio  $1569.00

bullet

Models with PVC or HDPE (chemically resistant)  pump heads and/or TFE seals (chemically resistant) are available -  call for application

bullet

Link to HydroBlend 6000 Series Table listing all models with size, ratio, GPM, and common industry uses

bullet

Model with dual injection pump - click on link below for detailed description and pictures HydroBlend dual injection proportioning pumps

bullet

Easy to install complete rebuild kits are also available.  Call for pricing.  Some of the most popular are:

bullet

RK 6120-V  $153.60

bullet

RK 6180-V  $159.06

bullet

RK 6200-V  $160.55

bullet

Rebuild kits with TFE seals are slightly higher:

bullet

RK 6040-TFE  $190.25

 

 

MV6200 A-V

Proportional Mixer

 

 HydroBlend™ Mid Volume (MV) Series Water Powered Proportioning Pumps

Can be used with hose reels, in-line, and in central mixing systems. Very accurate.  Typically used for higher volume applications such as auto-fill, central coolant distribution systems, or larger tanks. 

bullet

12 gpm @ 75 psi

bullet

Acrylic pump head standard

bullet

Viton seals standard 

bullet

Stainless steel valve block, outlet fitting, and main cylinder

bullet

Reduces chemical waste, improves proportioning accuracy, repeatable formulations, easy installation, and reliable operation

bullet

Water pre-filter included - 150 mesh/65 micron cleanable screen, garden hose fittings  

bullet

MV6120 A-V  12 oz. - .95% to 9.10% mix ratios $1129.00

bullet

MV6200 A-V  20 oz. - 1.60% to 13.50% mix ratios  $1237.00

bullet

MV6300 A-V  30 oz. - 2.40% to 20.00% mix ratios  $1348.00

bullet

MV6540 A-V  54 oz. - 4.70% to 40.00% mix ratios  $1801.00

bullet

Alternative pump head materials:

A - Acrylic (standard)

PVC - Polyvinylchloride (standard)

HDPE - High Density Polyethylene (chemically resistant)

bullet

Alternative seal combinations:

V - Viton (standard)

E - EPDM (standard)

TFE - Teflofluorethlyene (chemically resistant) 

 

 

HV6140 A-V

Proportional Mixer

 

HydroBlend™ High Volume (HV) Series Water Powered Proportioning Pumps

Can be used with hose reels, in-line, and in central mixing systems. Very accurate.  Typically used for higher volume applications such as auto-fill, central coolant distribution systems, or larger tanks. 

bullet

25 gpm @ 75 psi

bullet

Acrylic pump head standard

bullet

Viton seals standard 

bullet

Stainless steel outlet fitting and main cylinder, Noryl valve block, and PVC check valve on the outlet side

bullet

Reduces chemical waste, improves proportioning accuracy, repeatable formulations, easy installation, and reliable operation

bullet

3/4" NPT fittings standard, with 3/4" garden hose adapters included

bullet

Water pre-filter not included with high volume pump, but 65 micron or less is required for warranty

bullet

HV6090 A-V  9 oz. - .67% to 6.70% mix ratios $1660.00

bullet

HV6140 A-V  14 oz. - 1.00% to 10.00% mix ratios  $1663.00

bullet

HB6200 A-V  20 oz. - 1.60% to 13.50% mix ratios  $1732.00

bullet

HV6360 A-V  36 oz. - 3.20% to 26.80% mix ratios  $2055.00

bullet

More models available -- call for pricing

bullet

HV9256  High volume 50 micron water pre-filter and cartridge assembly  $75.00 (if ordered with pump)

bullet

Note:  The mixture ratios and percentages presume chemicals with the approximate viscosity of water.  A substantial increase in viscosity can reduce the proportioning specifications of the pump. 

bullet

Alternative pump head materials:

A - Acrylic (standard)

PVC - Polyvinylchloride (standard)

HDPE - High Density Polyethylene (chemically resistant)

bullet

Alternative seal combinations:

V - Viton (standard)

E - EPDM (standard)

TFE - Teflofluorethlyene (chemically resistant) 

bullet

Alternative injection cylinders:

SI - Single Injection

DI - Dual Injection

TI - Triple Injection

 

 

SuperDos Injector

 

 

 

 

Twist II Clean Filter

Dosmatic® SuperDos 20 Non-Electric Water-Driven Proportional Injector

The SuperDos Professional line of injectors continues Dosmatic's unmatched commitment to quality and reliability, while providing the industry's widest range of operational specifications.  The SuperDos has the lowest Low Flow and highest High Flow of any comparable water-driven injector, with the lowest pressure loss.

Features:

bullet

Injection ranges from 1:4000 to 1:10

bullet

Interchangeable lower ends

bullet

Patented mixing chamber (patented one way gasket prevents chemical contact with motor piston)

bullet

Standard proprietary body material exceeds PVDF for chemical compatibility without any extra cost

bullet

Ability to adjust ratios while in operation

bullet

Ability to change wear parts without opening upper body

bullet

3 year warranty

Additional benefits to customer:

bullet

The only non-electric, water-driven injector where the chemical is mixed in a patented internal mixing chamber separate from the motor, extending the life of the motor and reducing service and replacement costs.

bullet

Proprietary blend of highly chemical compatible materials results in a significantly stronger body and cover, allowing for the industry's highest operating pressure capabilities.

bullet

Lower body has more open ports entering and exiting the unit, reducing pressure loss.

bullet

Innovative mixing chamber design ensures a thorough and precise mixing of the water and injected chemical before leaving the unit.

bullet

SD20-10% - 15 gpm, 2.00% to 10.00% mix ratio, 5.0 - 100 psi, 1" npt inlet/outlet pipe connection  $695.00

bullet

More models available - call for application

bullet

015670 - Twist II Clean 104 micron inline water pre-filter 1"  $68.00  ($45.00 if purchased with SD20)

bullet

015570 - Twist II Clean 104 micron inline water pre-filter 3/4"  $63.00  ($41.00 if purchased with SD20)

 

Hydro Blend™ and Dosmatic™ serve many diverse industries and applications and carry many different models and products.  If you have an application other than industrial fluids, contact us, and we'll be happy to connect you with the right product.

Dave & Mary Schutter

Email   info@coolantconsultants.com

Phone (507) 451-8537 

Fax (507) 451-5155

 
Coolant Consultants, Inc.
1780 Cedar Avenue North
Owatonna, MN  55060